Blog

Water Heater Repair Miami Blog

Our blog is designed to give homeowners as much information on general plumbing repair tips, not just Miami water heater repair advice.  Many home plumbing maintenance tasks homeowners can be well equipped  to take care of themselves.  Enjoy!

Save Money on Your Miami Hot Water Bill

Posted by on Jan 4, 2014 in Plumbing Repair Miami, Water Heater Repair Miami | 0 comments

This time of year throughout the cold weather heating season, most individuals are conscious of attempting to save cash on heating the home. This makes it an excellent time for being effective with ones water heating too, especially because it generally accounts for around 18 percent of the average utility costs each month.

Water Heater Repair Miami’s 4 Ways to Save Hot Water Expenses

The 4 basic methods to lower ones water heating costs at home are reasonably basic: do not make use of as much hot water, turn down the thermostat temperature setting on the water heater, include insulation to the hot water tank and pipes, and replace an older system with an energy efficient one, those with the ENERGY STAR® label. Let’s take a look at these in some even more information now.

Using Less Hot Water

This could appear challenging however many of the ways in which to do so are not that hard or expensive to do. For instance, by replacing faucets and showerheads with low-flow, aerating designs will lower the amount of water made use of. An additional obvious tip is to repair any faucets that have leakages. It is amazing how much water is wasted from an apparently basic faucet drip! That water accumulates fast as an extra cost even if it is not hot water that is dripping.

Insulation

There are various insulation kits one can buy that will cover the whole water heater tank. These work well. For gas or oil units, simply make certain not to cover the top or bottom of the tank, the thermostat as well as the burner compartment in order for the device to work effectively. As for electric designs, just require to have the thermostat uncovered.

The initial six feet of pipe, both hot and cold, from the water heater need to be wrapped in insulation too. One can likewise install heat traps on the hot and cold pipes at the water heater if ones existing water heater does not currently have them built-in. Many more recent models do.

Thermostat Settings

Most recommend turning the thermostat to a minimum of 120 degrees. Yes, this will help save energy expenditures. There is, nonetheless, dispute over germs growing at 120 degrees or less. OSHA recommends a setting of 140 degrees. With this setting at the water heater itself, the actual tap temperature level will be more like 122 degrees. This is the best setting for those worried about Legionnaires’ illness, where the organism can grow at temperature levels less than 122 degrees. On the various other hand, those with younger children will not want the water to be too hot either.

Water Heater Replacements with Energy Efficient Models

This goes not simply for water heaters, however for dishwashers and clothes washing machines too. The majority of water heaters last 10 to 15 years is maintained well. Though the ones available today are much more energy reliable than those from 10 years ago. The most energy effective ones do cost even more but typically last longer and will minimize energy expenses over the life of the unit.  The US Department of Energy has tips on shopping for appliances here.

Tankless water heaters may be an excellent alternative relying on the amount of hot water one utilizes, or choosing a heat pump water heater too. These make use of half the electrical power than a standard electric water heater. They can also assist dehumidify ones house in the summer months when found in the basement.

Solar water heaters can be an excellent choice is one has the right quantity of sunshine on a south-facing roofing system, especially if going electric is what one needs to utilize. The following video is on a solar water heater installation in Canada:

There are various tax cost savings and state incentives that are offered too. Inspect out the Database of State Incentives for Renewables & Efficiency for help.  Here is also a nice energy calculator by the Home Energy Saver as well.

Water Heater Repair Miami hopes this has been a great starting point for you with taking steps to save money on the hot water made use of at house.

Enhanced by Zemanta

Toilet Terminology

Posted by on Dec 28, 2013 in Toilet Repair Miami, Water Heater Repair Miami | 0 comments

With half of the December holidays behind us, Water Heater Repair Miami decided to have a little fun this week and wished to share a new infographic by Phil Luther with you. It is exactly 7 months to the 104th anniversary of John Crapper’s death (July 27), the individual to whom the development of the flush toilet is usually related to. Actually, in 1596 John Harrington created the modern-day flush toilet, though Crapper did further the development of the toilet and held many essential plumbing patents that made toilets work much better and in a more hygienic way.

Your toilet might be working a little overtime this holiday season if you have had many visitors and family in from out of town. We recommend for everybody to be mindful of what all gets flushed so you won’t have to call us for any toilet repairs. Attempt to keep a trash can in plain sight next to the toilet so visitors will utilize it and not flush items that you would not typically flush yourself … maybe keep a plunger in plain sight too, just in case.

Delight in the list of synonymous terms for the word “toilet” here and delight in the rest of the season!

Toilet Repair Miami

Don’t miss our service page Toilet Repair Miami too!

How to Avoid a Miami Water Heater Explosion

Posted by on Dec 16, 2013 in Water Heater Repair Miami | 0 comments

No, it does not happen that typically, thankfully, however a water heater has the potential to blow up and trigger major damages to a house and people. It is simple to have the state of mind that it is something that occurs to various other people, however without appropriate care of ones water heater, it could possibly happen to you.

Water Heater Repair Miami does not wish to seem like an alarmist, but wished to share some various videos we assembled from around the Internet to show this point.

The first one is news footage from a Phoenix homeowner whose electric water heater blew up quickly after he was performing some upkeep on the heater.

The next example video is from Walnut, CA. it is shared by WaterHeaterExplosions.com and the storyteller does an excellent task of discussing exactly how the surge took place and exactly what kinds of actions a resident can require to avoid it.

So exactly what are the means to avoid this from taking place in your home? There are some easy regular maintenance actions property owners can do. However, we cannot worry enough to have a professional have a look at your water heater periodically too, to see to it it is working properly.

For “fun”, some individuals like to check this theory. The following video holds true with a 50 gallon water heater that reached 330 psi of pressure.

Probably the most well seen video of examining this concept is from Mythbusters, due to the fact that they just like to blow things up. Take pleasure in the final video and bear in mind that water heater safety is not something to be taken for granted or lightly.

Water Heater Repair Miami’s Related Articles

How to Get Rid of Miami Water Heater Odors

Miami Water Heater Safety Precautions

How to Get Rid of Miami Water Heater Odors

Posted by on Dec 10, 2013 in Water Heater Repair Miami | 0 comments

If you have foul water originating from your water heater follow Water Heater Repair Miami’s directions below to obtain your water smelling and tasting better.

The Causes of Miami Water Heater Smells?

According to Soquel Creek Water District, “The smell is the result of four factors that must all be present for the odor to develop. These factors include:

  • A high concentration of sulfate in the raw water
  • Sulfate reducing bacteria, non-toxic to humans (sulfate is reduced to a sulfide state by the bacteria)
  • Little or no dissolved oxygen in the water
  • Hydrogen (a component of water which may be present due to water conditions reacting with the anode)”  Read more: http://www.soquelcreekwater.org/content/how-get-rid-odor-water

The most usual reason for hot water smell is germs in the water supply.
This is more common in houses that utilize well water and cities that make use of wells as their water source.

Setting your water heater temperature at 140 degrees or above ought to help lower bacteria development.

How you can remove foul-smelling water.

The directions are for cleaning your water heater with chlorine bleach (clorox).

Turn off the electric or gas supply to the tank.

Turn off the cold water supply to the tank.

Open the hot side of the kitchen faucet to allow air to get in the tank.

Connect a yard hose to the drain valve and drain water heater.

Close the drain valve.

Now you require a way to get the bleach into the tank.
If your water heater has a flexable line where cold water enters the tank, unscrew the line from the tank.
If not, get rid of the pressure relief valve. An element could be gotten rid of from an electric water heater.

Make use of a funnel to pour the bleach into the opening.
Use 5 ounces of bleach for every gallon of the tank capability.
Example – A 50 gallon water heater would require 250 ounces of bleach (about 2 gallons).

Reinstall the water line or relief line.

Refill the tank with water.

Close the hot side of the kitchen faucet as quickly as all the air runs out the line.

Run all hot water components (consisting of the dishwasher and clothes washer) till you smell bleach.
The idea is to kill the germs in the water lines likewise.

Let the water stand in the water heater tank and water lines undisturbed for 2 to 3 hours.

Drain your tank once again and refill it. Let it set undisturbed for 30 minutes and drain the one more time.

Refill the tank. Open all of the hot water fixtures and let them run till the odor of bleach is gone consisting of the dishwasher and clothing washer.

Gas Water Heaters
Relight the water heater pilot burner.

Electric Water Heaters
Turn the power back on.

If the drain valve congests up when your tring to drain the tank go to the flush hot water heater page to see exactly how to change the drain valve with a ball valve.

You may need to duplicate this procedure more than once but normally one time looks after foul-smelling water or water heater odor.

Also, by changing ones anode rods, and even the type used can do the trick as the following video illustrates:

More Resources

Controlling Odors in Hot Water Heaters – City of Fellsmere

Solving rotten-egg odor in water heaters

Your Household Water Quality: Odors in Your Water

How Thermocouples Work on Ones Miami Water Heater

Posted by on Dec 9, 2013 in Water Heater Repair Miami | 0 comments

Ok, not to get too technical with you today, but Water Heater Repair Miami wants to share some information on a water heater’s thermocouple.

The Family Handyman correctly concluded that “when thermocouples wear out, the pilot light goes out, the burner won’t light, and you don’t get any hot water.”

Standard design
Likewise called universal water heater thermocouple. It screws into the bottom of the gas valve and a probe on the other end slides into a holding bracket near the pilot light. It looks like a piece of copper wire.

Universal thermocouples can be found in lengths from 15 to 36 inches. An 18 or 24 inch will suffice for all residential water heaters making use of universal kits. Virtually all older waters heaters and numerous of the more recent design units with a closed burner compartment and a seeing window will utilize this thermocouple.
If you want to use an exact replacement length simply eliminate your old one and measure it.

TCO design

Thermal Cut Off design has a re-settable thermal shut off switch important into the thermocouple. In case of a flash fire or blow back from the burner the TOC will close down gas flow to the burner and pilot. In case of a shut down the TOC ought to reset itself after it cools down and permit you to relight the pilot. The TOC switch appears like a watch battery. You will just discover the TOC on more recent design water heaters with seal burner compartments.

TOC non-resettable style

These thermocouples have a small TOC build inside the tube. They look much like a basic one other than the diameter is bigger about midways of television. When these TOC’s turn off they will not reset and have to be replaced.

How Thermocouples Work

A pilot thermocouple sends out a tiny electrical current to the gas valve when the probe is heated to a specific temperature. This electrical current informs the gas valve that the pilot is lit and its ok to send out gas to the burner if the thermostat calls for it.  There are some great images to illustrate how this works here.

To test a water heater thermocouple push the pilot button down on the water heater gas control valve. Then light the pilot. If after holding the pilot button down 30 to 60 seconds the pilot light doesn’t stay on when you let go of the button, the thermocouple is most likely at fault on older systems. The TOC or air flow could be the problem on newer devices with a pilot light viewing window.

If the pilot does not light at all the issue is gas flow, gas control valve, TOC tripped.

Usual Thermocouple Problems

The most common issue is the idea on the thermocouple probe degrades. It can easily be replaced.

Thermocouple Repair

If the probe looks white this is carbon build up. It could keep the probe from getting hot enough to send out a signal to the gas valve. Try sanding it with emery cloth and relight the pilot. It needs to work for a while however keep a brand-new thermocouple handy.

  • The thermocouple probe must be in the pilot light flame.
  • The thermocouple needs to be screwed into the gas valve securely.
  • Inspect the pilot thermocouple tube for kinks.

Water Heater Repair Miami hopes this has actually been a great introduction to a water heater’s thermocouple for you!

Miami Water Heater Safety Precautions

Posted by on Dec 4, 2013 in Plumbing Repair Miami, Water Heater Repair Miami | 0 comments

Appropriately preserving ones water heater is vital not so it works to its full capacity and can save some energy cash, but for safety issues too. Yes, it can blow up – it does not take place too typically for homeowners, but obviously this is something that Water Heater Repair Miami does not wish to have take place to you!

Vents
Venting can be sort of technical however we will review the basics right here. The vent should be the same diameter as the draft diverter of the water heater tank. It is supposed to increase and out (for atmospherically vented heaters). Not various other directs like up, down, up and out. For direct-vent water heaters, the vent should head out a side wall. As for power-vent heaters, the fan blows the fumes out, so there is some flexibility in the instructions they are vented.

Any roofing or wall that the vent goes through should be a double wall. The single wall pass throughs should be screwed with 3 screws per area. If these basics are not followed, the vents can break down with time and carbon monoxide can cause significant troubles within ones home. Obviously we do not desire that to occur!

The only other interested in ventilation is that of backdrafting. The fumes can eat the vents with acid condensation. If plenty of this gets on cold piping and the water heater it will not be a good situation for a correctly working water heater. If the fumes return inside the instead of being correctly vented outside, the fumes can enter the living locations of the home. Soot troubles can develop also.

Dielectric Connectors
The steel water heater is linked to cooper pipes by the dielectric connectors. When 2 these 2 metals are put together in water electrolysis happens. The process wears away one metal away to safeguard the other. This process is essential in shielding the inside of the water heater. Inspection for leakages ought to be done where the connections are made.

Temperature and Pressure Relief Valve
This is kinda of a crucial part of the water heater, for it assists to make certain the darn thing does not explode under pressure if the temperature level goes beyond the appropriate limitations the water heater is designed for. Once a year (a minimum of) the T&P valve should be checked to see to it, it is working effectively, for they can be susceptible to failure. Simply pulling up on the handle water needs to stream easily out and stop when the handle is let go of. If it just runs or trickles, or does absolutely nothing at all, it will should be replaced.

The drain lines for the T&P line ought to not be directed up, because water does not stream uphill too well. Ensure it goes down and or out please. If water is running out the drain line frequently, it is the indicator of something wrong too. It can be among a number of various things that we will not enter here – simply call a neighborhood plumbing technician please.

Earthquake Straps
Yep, even if you do not live in an earthquake zone and are needed to have these on ones water heater, it is an excellent idea to do so. It seems like most all brand-new homes in sub-divisions nowadays have the water heater in the garage. Yes, there is typically a concrete curb in front of it so one does not drive an automobile into it, however things can unintentionally knock it over so be safe and strap that thank in.

Temperature Level Setting
It seems most residential water heater tanks have setups of warm – hot – very hot … and not degree markings. Some “suggestions” on saving energy in your home particularly in the winter time, say to lower the setting on the tank to 120 degrees. That’s fantastic for conserving energy however legionella bacteria, which triggers Legionnaire’s disease can grow at 120 degrees. By breathing in the mist from the water in the shower, one can inhale the bacteria. Look for a medium in between 130 and 120 degrees. Above 130 degrees is technically a scalding temperature so beware.

Anode Rods
These normally are made of aluminum and there is absolutely nothing incorrect with that in theory, though we recommend using magnesium ones. Let’s state for whatever reason there is some sort of emergency or disaster where one lives and one needed to use the water in the water heater for drinking water (since bunches of emergency readiness people advise doing so). The water that comes out of the drain valve is the water at the bottom of the tank. If one has aluminum anodes, that water will be packed with aluminum substances, which is bad for the body. It is bad for the stomach, intestines and joints.

The anodes assist with rust defense and are crucial in extending the life of the water heater. They can likewise assist with odor issues with the water. Generally, magnesium anodes just work much better for a great deal of various reasons like the health benefits, let develop of sediment, a quieter water heater, and they have the tendency to work more competent with softened water.

Drain Valve
Ok, simply inspect it a minimum of once a year to make sure the darn thing opens and works. And it is excellent to drain and purge the tank a minimum of once a year anyhow (something you of course are doing already). If for some reason one should make use of the water during a catastrophe or drain it to quite a loud tank and have not drained it frequently, and it does not open, it will take longer to remedy the issue you are at first trying to take care of.

Combustion Changer Hatch
Since gas and oil water heaters breathe the air drawn in from underneath, combust with it and exhale it, it is crucial to keep the area around it, specially below the water heater, clean and swept. If if is not burning correctly, it can cause composing issues (mentioned above), in addition to combustion and fume issues and possibly be a fire hazard. Some of examining the chamber and how the flame burns is objective so we are not going to enter a great deal of detail below. it is essential to see if the combustion chamber roof has a great deal of rust or water markings or is black in color. These are not a good indicator at all. One need to see some blue flame at the bottom when it burns and orange and yellow at the top, nonetheless, the yellow need to not be incredibly high up. One need to see gray metal, some white condensation marks are ok.

Water Heater Repair Miami has put together an infographic to highlight the information above:

Water Heater Repair Miami